 |
® |
| Projection Height Range | |||||||||||
|
Lancer-1 Only |
LANCER-1 and LANCER-2 |
LANCER-2 Only |
Trip Gage | ||||||||
| Stud Size | #8, #10, M4, M5 | 1/4", M6, M7 | 5/16", M8 | 3/8", 7/16", M10 | |||||||
| Inches | mm | Inches | mm | Inches | mm | Inches | mm | ||||
| Stud Projections | MIN | .313" | 7.9mm | .406" | 10.3mm | .500" | 12.7mm | .500" | 12.7mm | #1 Open Gage | |
| MAX | .470 | 11.9 | .525 | 13.3 | .750 | 19.0 | .625 | 15.9 | |||
| MIN | .406 | 10.3 | .500 | 12.7 | .594 | 15.1 | .594 | 15.1 | #10 Gage | ||
| MAX | 1.625 | 41.2 | 1.719 | 43.6 | 1.813 | 46.0 | 1.813 | 46.0 | |||
| MIN | .556 | 14.1 | .650 | 16.5 | .744 | 18.9 | .744 | 18.9 |
#10-AL Auto-Load Gage |
||
| MAX | 1.775 | 45.1 | 1.869 | 47.4 | 1.963 | 49.8 | 1.963 | 49.8 | |||
| MIN | .811 | 20.6 | .905 | 23.0 | 1.000 | 25.4 | - | - |
LANCER-1 #10-ML Machine Load Gage |
||
| MAX | 2.027 | 51.5 | 2.122 | 53.9 | 2.216 | 56.3 | - | - | |||
| MIN | - | - | .822 | 20.9 | .916 | 23.3 | .916 | 23.3 |
LANCER-2 #10-ML Machine Load Gage |
||
| MAX | - | - | 2.041 | 51.8 | 2.135 | 54.2 | 2.135 | 54.2 | |||
| MIN | 1.563 | 39.7 | 1.656 | 42.0 | 1.750 | 44.4 | 1.750 | 44.4 |
#11 Gage #11-AL Gage #11-ML Gage |
||
| MAX | 2.781 | 70.6 | 2.875 | 73.0 | 2.969 | 75.4 | 2.969 | 75.4 | |||
|
NOTE: ±.031"
or ±0.8mm tolerance on
all projection heights. If stud projection requirements are longer or shorter than those shown above, consult TITAN TOOL COMPANY for special options or tool modifications. |
|||||||||||
| Projection Height Adjustment | |||||||||||
|
Tools shown are Lancer-2's equipped with a #10 Gage. Increasing the distance between lock rings "A" and "B" will produce a corresponding increase in the set projection height.
|
|||||||||||
| Two Stage, Anti-Strip Loading / Unloading Cycles | |||||||||||
|
Whenever the LANCER is used on a projection height application it is essential that you specify that the tool be equipped with a "P" Body. The "P" Body allows the Drive tang and slot to completely disengage. This totally isolates the body, jaws and stud from any rotational force. This unique two stage loading / unloading cycle prevents thread damage that commonly occurs with projection height stud drivers that utilize a conventional single stage design. Exception: If projection height of stud is controlled by Spindle Stop, and Spindle Rotation stops at the same time as Spindle Feed stops, then use ET-Body for improved performance. |
|
||||||||||
|
|
Previous Page |
Page 5 of 11 |
 |
|||
|
Click Here To Submit Your Application And Receive A Prompt Quote |
||||||
| RETURN TO TOP OF PAGE | RETURN TO HOME PAGE | CONTACT TITAN TOOL COMPANY | ||||
| Revised: 08/22/03 | ||||||
